ifconfig vs ip: What’s Difference and Comparing Network Configuration

Linux based distributions have featured set of commands which provide way to configure networking in easy and powerful way through command-line. These set of commands are available from net-tools package which has been there...

Spread the love

Linux based distributions have featured set of commands which provide way to configure networking in easy and powerful way through command-line. These set of commands are available from net-tools package which has been there for a long time on almost all distributions, and includes commands like: ifconfig, route, nameif, iwconfig, iptunnel, netstat, arp.

Ifconfig Vs IP Command

Ifconfig Vs IP Command

These commands are just about sufficient in configuring the network in a way any novice or an expert Linux user would want, but due to advancement in Linux kernel over past years and unmaintainable of this packaged set of commands, they are getting deprecated and a more powerful alternative which has ability to replace all of these commands is emerging.

This alternative has also been there for quite some time now and is much more powerful than any of these commands. Rest of sections would highlight this alternative and compare it with one of the command from net-tools package i.e. ifconfig.

ip – A Replacement for ifconfig

ifconfig has been there for a long time and is still used to configure, display and control network interfaces by many, but a new alternative now exists on Linux distributions which is much more powerful than it. This alternative is ip command from iproute2util package.


Although this command might seem a bit complex at first site but it is much broader in functionality than ifconfig. It is functionally organized on two layers of Networking Stack i.e. Layer 2 (Link Layer), Layer 3 (IP Layer) and does the work of all the above mentioned commands from net-tools package.

While ifconfig mostly displays or modifies the interfaces of a system, this command is capable of doing following tasks:

  1. Displaying or Modifying Interface properties.
  2. Adding, Removing ARP Cache entries along creating new Static ARP entry for a host.
  3. Displaying MAC addresses associated with all the interfaces.
  4. Displaying and modifying kernel routing tables.

One of the main highlight which separates it from its ancient counterpart ifconfig is that latter uses ioctl for network configuration, which is a less appreciated way of interaction with kernel while former takes advantage of netlink socket mechanism for the same which is a much more flexible successor of ioctl for inter-communication between kernel and user space using rtnetlink (which adds networking environment manipulation capability).

We can now begin to highlight the features of ifconfig and how they are effectively replaced by ip command.

ip vs ifconfig Commands

Following section highlights some of ifconfig commands and their replacement using ip commands:

1. Displaying all Network Interfaces in Linux

Here, one distinguishing feature between ip and ifconfig is that whereas ifconfig only shows enabled interfaces, ip shows all the interfaces whether enabled or disabled.

ifconfig Command
$ ifconfig
ifconfig: Check IP Address

ifconfig: Check IP Address

ip Command
$ ip a
ip: Check IP Address

ip: Check IP Address

2. Adding or Deleting an IP Address in Linux

The below command assigns the IP address 192.168.80.174 to the interface eth0.

ifconfig – Add/Del IP Address
# ifconfig eth0 add 192.168.80.174

Syntax for adding/removing an interface using ifconfig command:

# ifconfig eth0 add 192.168.80.174
# ifconfig eth0 del 192.168.80.174
ip – Add/Del IP Address
# ip a add 192.168.80.174 dev eth0

Syntax for adding/removing an interface using ip command:

# ip a add 192.168.80.174 dev eth0
# ip a del 192.168.80.174 dev eth0

4. Add MAC Hardware Address to Network Interface

The below command sets the hardware address for the interface eth0 to the value specified in the command. This can be verified by checking the HWaddr value in the output of ifconfig command.

ifconfig – Add MAC Address

Here, the syntax for adding MAC address using ifconfig command:

# ifconfig eth0 hw ether 00:0c:29:33:4e:aa
ip – Add MAC Address

Here, the syntax for adding MAC address using ip command:

# ip link set dev eth0 address 00:0c:29:33:4e:aa

4. Setting Other Configurations of Network Interface

Apart from setting IP address or Hardware address, other configurations that can be applied to an interface include:

  1. MTU (Maximum Transfer Unit)
  2. Multicast flag
  3. Transmit Queue length
  4. Promiscuous mode
  5. Enable or disable all multicast mode

ifconfig – Other Network Configurations

ip – Other Network Configurations

a. Set MTU value to 2000.

# ifconfig eth0 mtu 2000
# ip link set dev eth0 mtu 2000

b. Enable or Disable multicast flag.

# ifconfig eth0 multicast
# ip link set dev eth0 multicast on

c. Setting the transmit queue length.

# ifconfig eth0 txqueuelen 1200
# ip link set dev eth0 txqueuelen 1200

d. Enabling or disabling promiscuous mode.

# ifconfig eth0 promisc
# ip link set dev eth0 promisc on

e. Enable or disable all multicast mode.

# ifconfig eth0 allmulti
# ip link set dev eth0 allmulti on

5. Enabling or Disabling Network Interface

The below commands enable or disable specific network interface.

ifconfig – Disable/Enable Network Interface

The below command disables the interface eth0 and it is verified by output of ifconfig which by default shows only those interfaces which are up.

# ifconfig eth0 down

To re-enable the interface, just replace down by up.

# ifconfig eth0 up
ip – Disable/Enable Network Interface

The below ip command is alternative for ifconfig to disable a specific interface. This can be verified by the output of 'ip a' command which shows all the interfaces by default, either up or down, but highlights their status along with the description.

# ip link set eth0 down

To re-enable the interface, just replace down with up.

# ip link set eth0 up

6. Enable or disable the use of ARP protocol

The below commands enable or disable ARP protocol on specific network interface.

ifconfig – Enable/Disable ARP Protocol

The command enables ARP protocol to be used with interface eth0. To disable this option, just replace arp with -arp.

# ifconfig eth0 arp
ip – Enable/Disable ARP Protocol

This command is the ip alternative to enable ARP for the interface eth0. To disable, just replace on with off.

# ip link set dev eth0 arp on

Conclusion

Thus, we have highlighted features of ifconfig command and how they can be done using ip command. Currently, Linux distributions provides a user with both the commands so that he can use according to his convenience. So, which command is convenient according to you which you would prefer to use? Do mention this in your comments.

If you want to learn more about these two commands, then you should go through our previous articles that shows some practical examples of ifconfig and ip command in more detailed fashion.

Don’t Miss: 15 “ifconfig” Examples to Configure Network Interface in Linux

Don’t Miss: 10 “ip” Command Examples to Configure Network Interface in Linux

Facebook Comments
Spread the love

Posted by News Monkey